Tuesday, October 30, 2007

Monday - Rope Burns!

Today was spent putting the bindings in place. Once again I thought, piece o' cake. Wrong. George guided us through the process and it went pretty well. At the end of the day, everyone's bindings were glued in and ready to sand!


First we needed to clean out the binding channels with a chisel.


Then we glued and "clamped" the binding to the guitar body.
Lower binding done!

Ready to sand and finish!!!!

Sunday, October 28, 2007

Sunday - Covered Bridges and Mountains

I rented a car for the last week, as I felt it would be good to get away for a little while every now and then. Sunday, being our day off, started off with laundry and a call to Peg. Then it was off to places unknown. Took a few side roads - Vermont has no billboards - I mean NO BILLBOARDS! It is awesome. There are little signs at the side of the road pointing out places of interest. I saw a sign with Von Trapp on it. I made a sharp left, knowing Peg would want me to do a "Sound of Music" pilgramage for her. Didn't see any Von Trapp's, but ran into a neat covered bridge.



Took off for the Green Mountains. Beautiful, but I missed the fall colors by a week or so.


We could take a lesson from Vermont - rare to see a big chain store. Not a lot of cell phone towers. Hardly any homes built into mountains. Just trees. And beauty.

Watch out for Moose!

Saturday - Sweatin' Bullets

Today was an interesting day. After putting the body together, it is necessary to give it a finished appearance - all the seams do not quite fit together perfectly. It is necessary to put a small strip of decorative wood at the butt end. This was done by measuring perfectly and cutting a line with an x-acto knife resting against a straight edge. Then chiseling out the remaining pieces. Then fitting in the decorative piece. Surprisingly enough, this went fairly smooth and I feel real good about the end result.

Beginning the chisel process

The next thing to do was to put in a binding and purfeling channel. These are decorative strips of either plastic or wood surrounding the guitar body. In order to do this, one must use a router and a special fixture attached to it.

The router - or the little machine from hell.

Then carefully go around the guitar body and cut out the channels.

I went ahead and let Jack go first. Youth before age........

Piece o' cake, one might say. Knowing how a router operates, and knowing that it is moving at 20,000 rpm with a 1/4 inch bit that can rip a large mass of wood out of my precious guitar body made me just a tad nervous. Such a tad nervous that I was soaking wet by the time I was done with the process.
Not bad!
George being the master craftsman and master teacher made people feel at ease with the process, and developed an almost goof proof system to do it. Surprisingly, it looks pretty good! In fact, it looks great!

Saturday, October 27, 2007

Friday - I hear and I forget, I see and I remember, I do and I understand

Well, nothing is ever totally easy in this guitar making business. The back was an interesting problem to work out. If you look at the back of an acoustic guitar, you will note that it is curved both to top to bottom (heel to butt), and side to side. You may remember that I mentioned the gluing process was different on the back piece. We needed to plane down high spots that we could see by looking at the edges of the guitar and sighting in differences in levels. Then we contoured the edges with a special sanding block. To be honest, this was hard to understand until we actually got involved in the process and called George over to check no less than 3 times.

Contouring the sides in preparation for the back





Finished contoured back

We then prepared the back to fit, by scalloping the braces, checking the fit (this happened several times) the drawing the final cutting pattern out (we had left the back about 1/4 inch wider all the way around to prepare it for a perfect fit). We then made a final cut on the bandsaw.

We then "test" clamped the back to prepare for gluing. In this guitar making business, it is smart to prefit everything. We then glued and clamped the back.


Back clamped together



A few hours later we took the clamps off. Looks like a finished body, but nothing is ever easy in this guitar making business. Tomorrow - the edge bindings!


Thursday, October 25, 2007

It's a Guitar! (almost)


Today we glued the top to the soundboard. Sounds easy, but there was a great deal of preparation and planning to make sure that the 15 minutes of set time for the glue did not over-run into our clamping time. We had to prepare the tail block to the curvature of the guitar. Then re-clamp everything in place, check everything and glue! All went reasonably well with only one emergency call to George.


We then went to lunch, came back, took things apart and we had a guitar!



It does look pretty cool though! That's my t-shirt you are seeing. Got to do the back tomorrow!

The rest of the day was spent reinforcing the inside of the body with thin strips of veneer at key "cracking" points. We also prepared a special lamination for a future extra sound hole.

Wednesday, October 24, 2007

Week Two! Monday, Tuesday, and Wednesday

Week two has arrived - to be honest, one day runs into another.....What day is today?

Monday Bending sides!

We bent our sides, binding, and kerfing strips today and joined them together.



This is the side bending fixture. It has three 200 watt light bulbs inside and is what we used to form our binding strips, kerfing, and sides.



We then attached the kerfing strips to the sides. Notice the saw cuts in the strips that are attached to the sides. These are called kerfs. They allow the thick strips to bend rather easily, yet when bent provide a great deal of support for the sides, top, and back. Great engineering - thought of many years ago!



Tuesday - Hand tools and craft.

Watching a craftsperson at work is truly an amazing thing. Today George showed us how to take our bracing which was glued to the top last week and produce and instrument with tone. We used hand tools - chisels and little tiny hand planes about 1 inch long then cut down the bracing on the top. It took a piece of wood that sounded like a brick, and produced an instrument.

The beginning of day!

Finished!

George demonstrating how to check for tone on a soundboard.


Wednesday - Let's make something that looks like a guitar!

Today we worked on preparing the soundboard and neck to meet




We fit the neck and top together and checked alignment.

We then glued the neck block to the top.



We prepared the sides by hand planing and then running them through the jointer. Nothing like taking paper thin wood and running it through a machine that can rip your arm off!

Then we worked on cutting the sides and kerfing, adjusting the bracing, and attaching them to the top. Tomorrow we glue!

Monday, October 22, 2007

Sunday - Our day off

We ended up going to Home Depot so that we could purchase the materials to make our gluing form with. It is one of the harder pieces to design on our own due to the complex radii. We then ended up with an awesome fall color tour due to Victor relying on his GPS vs. using a map. It was worth it though, and we saw some Vermont and New Hampshire countryside.




I actually had time to take a walk around the lake when we got back "home." Ended up at a cemetery and walked around a little - appreciating the history of the area.